Duramax acceleration problems.

1 post · Joined 2014. #1 · Oct 3, 2014. 01 LB7, only non stock is air intake.I was pulling an average size boat when I got a check engine light and lost power. I could ease it up to 50 mph but if I pushed it then back down to no power. Pulled into a parts store,changed fuel filter and they analyzed it. Said it was the fuel pressure regulator.

Duramax acceleration problems. Things To Know About Duramax acceleration problems.

3. 384xray Discussion starter. 5 posts · Joined 2021. #1 · Feb 15, 2021. Hello all! I finally got the truck of my dreams having custom ordered, from the factory a 2021 2500 HD, CrewCab, 4x4, Z71. As of today it has 1227 miles on it and from day one there has been issues. 1st issue was pulling to the left which has now been back to the dealer ...Need help! I have a 2015 lml and I’m getting a p0087 low rail pressure code under hard acceleration, rail pressure stays with the desired pressure until 23,000 then the desired will go up to 29k as the actual rail pressure won’t exceed 23,500. Had a “change fuel filter” on the dash so I swapped the filter for a new on and the next day ...Sep 16, 2017 ... GM and GMC vehicles have been plagued by throttle position sensor problems along with the dreaded reduced engine power or limp mode.8. Loss of Power on Acceleration. The most common issues with an LLY Duramax diesel truck are loss of power at low revs under load and lackluster performance. This causes LLY Duramax engines to have issues accelerating, which can be dangerous.Jake goes over the background, common problems, reliability, and more for the Duramax LB7 engine. The article linked below, written by us, is a more in-depth guide on the common problems...

GM 6.6-Liter Duramax LML: CP4.2 … the Weakest Link. GM says the change from the CP3 pump used in the earlier models allows the LML to run on ASTM grade B20 biodiesel while ensuring more precise ...Best way I found to monitor truck is with an Edge Insight CTS. Oil life monitor jumps downward about 11% after every regen. I ignore the OLM. I go with oil analysis results to determine my change intervals and to make sure the is no fuel in oil. 2010 Gmc 2500 Duramax 853,500 Odometer miles - sold Nov 2018. 2013 LT CCSB SRW bought with 508,000 ...

Indices Commodities Currencies StocksThe Duramax is famous for rubbed through wire issues.. Pump up your fuel primer on the fuel filter head and let it sit (preferably overnight ). Recheck it in the morning and if the primer button is soft, start by rebuilding your fuel filter head or replacing it. Go through all fuel lines.

I will walk you through the 10 most common 2.8 Duramax problems with solutions. 1. Transmission Failure. 2.8L Duramax has a 6L50 transmission system. The same transmission system is used in Camaro V6, Holden Chevrolet Lumina, Chevrolet Caprice, Cadillac SLS, SRX, STS, and CTS engines. It means GM has used a car transmission system in mid-size ... Maybe. According to Pickup Truck Talk, the 2022 GMC Sierra 1500 has increasing reports of engine failure and no-stating issues. These problems include the gas-powered engines and the diesel option. The 6.1-liter V8 engine could be facing engine lifter problems. Owners of General Motors V8 engines with Active Fuel Management (AFM) …07 2500HD Classic Black crewcab\SB Duramax LBZ -Diablosport 120HP-Diamond Eye True downpipe-4" straight exhaust from band clamp back-AEM intake with AFE filter and outerwear-PPE EGR Blocker Plate-PPE fuel plug-Edge Insight W\EGT-BD Diesel manifold-Intake resonator bypassed-RCD 6" front, 2" rear blocks, Low profile bumpstops for lower arms.07 2500HD Classic Black crewcab\SB Duramax LBZ -Diablosport 120HP-Diamond Eye True downpipe-4" straight exhaust from band clamp back-AEM intake with AFE filter and outerwear-PPE EGR Blocker Plate-PPE fuel plug-Edge Insight W\EGT-BD Diesel manifold-Intake resonator bypassed-RCD 6" front, 2" rear blocks, Low profile bumpstops for lower arms.

2016 LML intermittent power loss and recovery. Just did a 3K trip on my 2016 over 3 days. Once each day for about 5 minutes while running at interstate speeds I had a power loss with excessive black smoke. Each time it lasted about 5 minutes and then was back to full power with no indications ever of any problems.

85 posts · Joined 2008. #1 · Jan 12, 2012 (Edited) My 2008 GMC Sierra D/A has started making a noise I never heard before when I'm Accelerating, I just had it in for oil change, fuel filter change, and alignment. This noise had started earlier but now it's more often, I don't think it is the Turbo. My gas mileage has also dropped about 2 ...

Teaching a child to read — and the importance of reading — can be a parent or teacher’s most difficult task, but the Accelerated Reader program makes it easier than ever. The progr...Yes, only 2,100. Already had it at the dealership twice. When I accelerate from a stop, there's a hesitation, then after a couple seconds, or when it gets to 10-15mph, it kicks in and takes off. The check engine light came on once around 800 miles, and I took it to the dealership.Indices Commodities Currencies StocksIt was making similar vibrations and similar acceleration problems. But it was in the rear and ended up seizing the rear shaft to the bearings cause I had straight pipe exhaust and couldn't hear it happening. ... A forum community dedicated to Chevy and GMC Duramax diesel owners and enthusiasts. Come join the discussion about …You buy a diesel because it makes 400 rwhp but when you push on the throttle from a stop the truck is slow to move - the pedal feels... dead. It's not until ...

Oct 11, 2010 · 2003 Chevrolet 2500HD 6.6L LB7 AFE stage 2 cold air intake, Straignt pipe 4" AFE exhaust, New Bosch injectors, High idle switch, Stanadyne fuel manager w/ 5 micron water seperator filter, CAT 2 micron fuel filter, Alliant lift pump, 285 75 16 Toyo M55's, Lund Sunvisor, FC5452. 3521 posts · Joined 2011. #4 · Aug 31, 2017 (Edited) Replace the oil pressure sending unit. Part number 12616646 $40. What was said above as well check the pig tail for rubs, switch is located right above and to the left of the oil cooler assembly on the driverside block. Sent from my iPhone using Tapatalk Pro.As a reminder, the 6.6L V8 L5P turbodiesel Duramax diesel engine found under the hood of the 2024 Chevy Silverado HD is rated at 470 horsepower at 2,800 rpm and 975 pound-feet of torque at 1,600 rpm.Aug 22, 2010 · Chevy / GMC Duramax 04.5-05 LLY Forum. 04.5-05 LLY Duramax Powertrain Acceleration Problems ... Acceleration Problems. Jump to Latest Follow ... 3. 1. Nov 17, 2022. #1. I just got a 2021 1500 3.0 Duramax with 15k on it. It is the Black Widow. I'm going to make a post about this strange squeal sound I hear under medium acceleration. Sounds like a balloon letting the air out while pinching the flap. IDK, I have had many turbos and this is not the turbo whistle.having a problem with light blue smoke at idle and heavy blue smoke on acceleration with it clearing away at cruse speed some say it is valve guides but upon going to the dealer the claim there are no valve guide seals on the duramax 6.6 and that that problem could be turbo seals anyone with any ideas? this is a 2002 silverado 6.6 …Need help! I have a 2015 lml and I’m getting a p0087 low rail pressure code under hard acceleration, rail pressure stays with the desired pressure until 23,000 then the desired will go up to 29k as the actual rail pressure won’t exceed 23,500. Had a “change fuel filter” on the dash so I swapped the filter for a new on and the next day ...

2018 L5P 3500 stumbles. New 3500 Denali bought new about 2 months ago. It has 1800 miles on it. while getting on the freeway at 35-45 mph relatively light acceleration truck stumbles I cant tell if its engine or trans caused. Kind of feels like it runs out of fuel or it doesn't know what gear to be in.2018 L5P 3500 stumbles. New 3500 Denali bought new about 2 months ago. It has 1800 miles on it. while getting on the freeway at 35-45 mph relatively light acceleration truck stumbles I cant tell if its engine or trans caused. Kind of feels like it runs out of fuel or it doesn't know what gear to be in.

Oct 25, 2022 ... Including hauling a truck camper all over the west up and down mountain passes in 90 deg temps without a single issue. Also performs well here ...Jake goes over the background, common problems, reliability, and more for the Duramax LB7 engine. The article linked below, written by us, is a more in-depth guide on the common problems...639 posts · Joined 2011. #2 · Dec 29, 2011. Smoke means your either getting to much fuel or not enough air. So with that being said I would start easy and see if you have a boost leak. Be sure you hot a clean air filter, and fuel filter. After that if you don't find anything I would move to the injection area. Maybe have you injectors checked.Feb 22, 2021 · New to me 2015 LML. Deleted and tuned (unknown tune) Feel stock power level wise but if you mat it it doesn't usually downshift it just slowly accelerates. Coming from an 08 lmm and if you mat it it will downshift and the rpms jump to 2500-3k and it goes. This new LML won't do that, it hasn't been an issue really but today I pulled my unloaded ... Slow acceleration, bad or no gear-shifting, and transmission overheating are the common signs of torque converter failure. If you notice these signs, be sure your torque converter is failing. You can do nothing but change the …Once you’ve identified the problem, it’s usually a straightforward repair job. 08. Fuel Pump Failures. If your engine sputters at high speeds or loses power during acceleration, a failing fuel pump could be your culprit. Fuel pump issues can lead to poor performance and can even leave you stranded on the road.Teaching a child to read — and the importance of reading — can be a parent or teacher’s most difficult task, but the Accelerated Reader program makes it easier than ever. The progr...

Bad hesitation on acceleration, NOT turbo lag! I have a 2006 LBZ that is starting to give me problems, I have 122,000 miles on it and it is very well maintained. The engine is all stock except for efilive DSP5 tuning, I have ran a nicktane 2 micron fuel filter since the truck was bought new. For some reason for the past 2,000 miles (only took a ...

Hooked up bluetooth scanner and read codes P128E & P0088 (high fuel rail pressure) reset the codes and took it for a ride. Seemed fine, but when I stood on the gas it wouldn't go over about 2900 RPM then check engine light with reduced power mode, and change fuel filter message. Swapped out the filter and took it for a ride with scantool …

Loaded weight for the first 1/2 of trip was 25,650 lbs for truck and trailer, empty weight was 14,850 lbs, I played around with speed coming home. Loaded at 60 mph I got about 11.5 mpg empty at 70 I got 8.9 mpg !!!! 2011 GMC Sierra 2500 HD 2500 4X4 Duramax Traded 162,000 miles!! 2019 GMC Sierra 3500 HD CC 4X4 Duramax SRW …Chevy / GMC Duramax 01-04.5 LB7 Forums. 01-04.5 LB7 Performance Parts Discussion ... Power loss on acceleration. ... I'm pretty much and a stand still right now although my I was having problems with my shift indicator so I changed the nsbu and ignition switch which fixed that problem but did fix what I think is a fuel issue ...The MAF values on the scanner should read as follows: With the engine idling at a temperature greater than 140°F and the Exhaust Gas Recirculation Valve (EGR) closed, the value of the MAF should be 38-42 g/s. With the EGR commanded on to approximately 40% the MAF should be 18 -22 g/s.Sound shows up on video at about 23 seconds. Ha ha I’m get that noise in the morning at around 15-20mph then it goes away never cared about it sounds like something rubbing a wire or something from the center counsel. The other thing that gets me temperamental is the Damb passenger seat belt when not flip correctly between the …2012 6.6 DEF continuous problems. Hi all, I'm here for help. I have a 2012 GMC 2500 6.6 I have 115,000 miles on it and over the past 50,000 miles I've had to have the DEF injector replaced and the entire DEF tank replaced. Last night I got the "poor" DEF fluid quality message with speed restrictions in 99 miles.Shudder under acceleration over 45mph. I’m getting a shudder/stutter when accelerating above 45mph. When I give it throttle above 45mph and it down shifts and puts the RPMs at 2,000, the shudder/stutter starts until 2,500 RPMs and then goes away. No issues under 45mph, during steady state driving, and it happen less when in tow haul mode. 2012 LML Duramax surges and has weak acceleration. I started to have issues when I was suddenly put into limp mode (couldn't go past 1000 rpms). Cleared the codes and it came out of it but with weak acceleration and surging while in gear as seen in the video. I took it back out to video the weak acceleration and it wasn't doing the surging ... 3. 1. Nov 17, 2022. #1. I just got a 2021 1500 3.0 Duramax with 15k on it. It is the Black Widow. I'm going to make a post about this strange squeal sound I hear under medium acceleration. Sounds like a balloon letting the air out while pinching the flap. IDK, I have had many turbos and this is not the turbo whistle.

Jul 21, 2022 · Maybe. According to Pickup Truck Talk, the 2022 GMC Sierra 1500 has increasing reports of engine failure and no-stating issues. These problems include the gas-powered engines and the diesel option. The 6.1-liter V8 engine could be facing engine lifter problems. Owners of General Motors V8 engines with Active Fuel Management (AFM) systems aren ... LML Surging on acceleration. I have a 2013 lml that when accelerating it will surge, happens more when under load pulling a trailer almost at any sort of acceleration rate. I've had this happening for the last 40k and no one knows how to fix it, no codes show. 112k I hit a deer and put new trans cooler, and bumper on the front, also did a 12mm ...LMM Duramax pistons can be burnt or damaged for various reasons. If you continuously use low-quality fuel in your engine, it will cause piston failure. Besides, extreme loads can …3.0 Duramax Problems and Solutions- Detailed Guide. Let’s examine some typical problems that users of this engine encounter and discover some practical fixes. Overheating Problems. One of the common complaints from the Duramax owners is that the water pump fails quite fast (it happens if you just drive around 80,000 miles).Instagram:https://instagram. quarry pool bataviahobby lobby keene photosfallout 76 fasnacht eventphillies diamond club perks Both types need a flow of oil all the time. If they do not have a flow of oil all the time, the friction increases and eventually there is bearing damage and this can lead to other damage in the engine.The loss of oil being pumped thru the engine can be varied; pump fails, passageway for the oil becomes blocked, etc. wsdot highway camerasscott d henry net worth Apr 12, 2017 ... Did u check your injectors rating and I think I'm having that same problem with mine mine are in spec and fuel mileage is getting bad after ... is there a mediacom outage in my area Had no problems until now.I have a 2001 2500 hd 6.6 diesel.Last month changed a bad water pump.Now having acceleration problems.Changed fuel filter. Still having problems. Starts good but has no passing power stuck at 65mph. Will work OK for a few days and starts over again.I have a '05 2500HD with the Duramax Diesel /Allison trans. and bought it with the stock air box and with it had very slow throttle reponse. I added on a Bully Dog Air Intake and did very little if anything to quicken it. It is most noticeable from a dead stop and hitting the throttle. It seems like it takes forever to kick in.Nov 17, 2018 ... If your LB7 is loping/surging at idle, especially when in drive, this is one possible solution to your issue. As stated in the video, ...